开云体育

网站公告:

新闻中心

开云体育(中国)集团公司

电话:0531-69951198

邮箱:jingtuolt@163.com

传真:0531-69951198

地址:济南市历城区西周南路9号

网址:http://keonnected.com

常见问题

当前位置:首页 - 新闻中心 - 常见问题 - 气液增压泵的原理特点以及

气液增压泵的原理特点以及应用

发布时间:2021-09-19 14:24:53   发布人:http://keonnected.com
气液增压泵是由压缩空气来驱动,增压液体,又称气动液体增压泵,可以将液体增压到640Mpa的压力。那么气液增压泵的原理特点以及应用是怎样的?小编为您讲解下。
The gas-liquid booster pump is driven by compressed air. The pressurized liquid, also known as pneumatic liquid booster pump, can pressurize the liquid to 640Mpa. What are the principles, characteristics and applications of gas-liquid booster pump? I'll explain it to you.
气液增压泵的原理
Principle of gas-liquid booster pump
气液增压泵工作原理类似于压力增压器,对大径空气驱动活塞施加一个很低的压力,当此压力作用于一个小面积活塞上时,产生一个高压。通过一个二位五通气控换向阀,增压泵能够实现连续运行。
The working principle of the gas-liquid booster pump is similar to that of the pressure booster, which applies a very low pressure to the large diameter air driven piston. When this pressure acts on a small area piston, a high pressure is generated. The booster pump can realize continuous operation through a two position five vent control reversing valve.
由单向阀控制的高压柱塞不断的将液体排出,增压泵的出口压力大小与空气驱动压力有关。当驱动部分和输出液体部分之间的压力达到平衡时,增压泵会停止运行,不再消耗空气。当输出压力下降或空气驱动压力增加时,增压泵会自动启动运行,直到再次达到压力平衡后自动停止。
The high-pressure plunger controlled by the check valve continuously discharges the liquid, and the outlet pressure of the booster pump is related to the air driving pressure. When the pressure between the drive part and the output liquid part reaches balance, the booster pump will stop running and no longer consume air. When the output pressure drops or the air drive pressure increases, the booster pump will automatically start and run until the pressure balance is reached again.
采用单气控非平衡气体分配阀来实现泵的自动往复运动,泵体气驱部分采用铝合金制造。接液部分根据介质不同选用碳钢或不锈钢,泵的全套密封件均为进口产品,从而保证了气液增压泵的性能。
The single air control non-equilibrium gas distribution valve is used to realize the automatic reciprocating motion of the pump, and the gas drive part of the pump body is made of aluminum alloy. Carbon steel or stainless steel shall be selected for the liquid connection part according to different media. The full set of seals of the pump are imported products, thus ensuring the performance of the gas-liquid booster pump.
气液增压泵的特点
Characteristics of gas-liquid booster pump
1、输出压力高,大输出压力可高达400Mpa。
1. The output pressure is high, and the large output pressure can reach 400Mpa.
2、使用范围广,工作介质可为液压油、水及大部分化学腐蚀性(相应的耐腐蚀材质密封)液体,并且可靠性高,免维护和寿命长。
2. It has a wide range of applications. The working medium can be hydraulic oil, water and most of the chemically corrosive (corresponding corrosion-resistant material seals) liquids, and it has high reliability, maintenance free and long service life.
3、易于调节,在泵的压力范围内,调节调压阀从而调节输入气压,输出液压相应得到无级调整。
3. It is easy to adjust. Within the pressure range of the pump, adjust the pressure regulating valve to adjust the input air pressure, and the output hydraulic pressure can be adjusted steplessly accordingly.
4、自动保压,无论何种原因造成保压回路压力下降,泵将自动启动,补充泄漏压力,保持回路压力稳定。
4. Automatic pressure maintaining: no matter what causes the pressure drop in the pressure maintaining circuit, the pump will automatically start to supplement the leakage pressure and keep the circuit pressure stable.
5、操作安全,采用气体驱动,无电弧及火花,可在危险场所使用。
5. Safe operation, gas driven, no arc and spark, can be used in dangerous places.
气液增压泵
气液增压泵的应用
Application of gas-liquid booster pump
航空工业
aviation industry
1、静态及动态测试设备
1. Static and dynamic test equipment
2、起落架负载、冲击试验
2. Landing gear load and impact test
3、飞机支架系统
3. Aircraft support system
4、液压服务小车
4. Hydraulic service trolley
5、胎裂(更换轮胎)
5. Tire crack (tire replacement)
6、拉伸成形
6. Stretch forming
7、阀门测试时夹紧
7. Clamping during valve test
8、飞机液压注油
8. Aircraft hydraulic oil injection
9、清洁剂的输送和高压清洗
9. Cleaning agent delivery and high-pressure cleaning
10、软管及圆管压力测试
10. Pressure test of hose and round pipe
11、压力表定刻度
11. Pressure gauge calibration
12、自动控制仪表截止阀
12. Automatic control instrument stop valve
13、发射塔拉力钢索的固定
13. Fixation of tension cable of launching tower
柴油机
Diesel engine
1、灌注燃料
1. Refuel
2、喷油嘴测试
2. Fuel injection nozzle test
汽车工业
automotive industry 
1、制动系统测试
1. Brake system test
2、倾斜驾驶室
2. Tilt cab
3、支架系统
3. Support system
4、拖车固定
4. Trailer fixation
5、操作离合器
5. Operating the clutch
6、压进、压出缸套
6. Press in and out cylinder liner
7、焊接压力容器的泄漏测试
7. Leak testing of welded pressure vessels
8、压轮胎入轮箍
8. Press the tyre into the tyre
9、变速箱泄漏测试
9. Transmission leak test
工业机器
Industrial machinery
1、滚动粉碎机(保持压力)
1. Rolling mill (holding pressure)
2、熔炉门的液压操作
2. Hydraulic operation of furnace door
3、低压接头的冷压成形
3. Cold forming of low pressure joint
4、等压机
4. Isopress
5、冲洗及冰箱冷凝器的静态测验
5. Flushing and static test of refrigerator condenser
6、橡胶品及胶卷的压制成形
6. Press forming of rubber products and film
7、剪切、冲压、压纹、定位、锻模、成形、切割及压制的动力
7. Power of shearing, stamping, embossing, positioning, forging die, forming, cutting and pressing
8、皮革及塑料制品的压纹成形
8. Embossing of leather and plastic products
9、露天潜孔钻机喷湿除尘
9. Wet spraying and dust removal of open down-hole drilling rig
气液增压泵的原理特点以及应用相关内容就讲解到这里了,您对此有什么想了解的问题或者说您有相关需求,可以随时来我们网站http://keonnected.com咨询联系,为您服务!
The principle, characteristics and application of the gas-liquid booster pump are explained here. If you have any questions or needs, you can come to our website at any time http://keonnected.com Consulting and contacting, serving you!
新闻推荐:
气体增压泵的使用六点注意事项 2021-10-05
采购及使用气液增压设备需注意几点 2021-09-25
气液增压泵的原理特点以及应用 2021-09-19
气体增压泵使用之前知道六要点 2021-09-17
气体增压泵如何工作以及如何维护 2021-09-15
气体增压泵和气液增压缸的工作原理不同 2021-09-05
怎么判断各类型的增压泵好与坏? 2021-08-26
通过表现来分析增压泵常见几种故障 2021-08-24
气体增压泵罐体进水了这样处理比较好 2021-08-17
阀门试验台使用前后的检查与注意 2021-08-05

13188935873

qq